Search found 412 matches

by n5tbu
Tue Nov 04, 2008 10:56 am
Forum: Kenwood Commercial Products
Topic: No Receive WHY
Replies: 4
Views: 6196

Re: No Receive WHY

The rec front end filters are very narrow and prob need tuning.
mod
by n5tbu
Tue Nov 04, 2008 10:54 am
Forum: Kenwood Commercial Products
Topic: TKR750 Program problems
Replies: 2
Views: 3892

Re: TKR750 Program problems

The version 1 software will not work on the ver 2 repeater.
mod
by n5tbu
Fri Aug 22, 2008 9:50 am
Forum: Kenwood Commercial Products
Topic: TKR-820
Replies: 1
Views: 3514

Re: TKR-820

Clean the eeprom and socket,I had the same problem before and now all is ok.
mod
by n5tbu
Thu Mar 27, 2008 6:55 am
Forum: Kenwood Commercial Products
Topic: No Tx on 762G
Replies: 3
Views: 4129

Re: No Tx on 762G

Any tech should be able to troubleshoot the problem....that model was famous for circuits going open on the front controller board,usually repaired by wiring jumpers from point a to point b.
mod
by n5tbu
Wed Mar 05, 2008 8:32 am
Forum: Kenwood Commercial Products
Topic: kenwood tk 830 speaker problem
Replies: 4
Views: 5089

Re: kenwood tk 830 speaker problem

That amp has a few inputs.....it is possible to have one section go bad and still get the power on beep. Try the amp board from another radio and see if it works,also could be a bad relay on the same board,try programming it for PA and see if that works.
mod
by n5tbu
Fri Feb 08, 2008 7:52 pm
Forum: Kenwood Commercial Products
Topic: 730/830 low power?
Replies: 7
Views: 7176

Re: 730/830 low power?

As stated above, it is possible. The power control is a varable resistor,if you knew the resistance you needed for the power level you desired,the aux button could be used to switch in that resistor. It would take some circuit board work and a little time. You would have to really want that feature ...
by n5tbu
Tue Feb 05, 2008 5:37 pm
Forum: Kenwood Commercial Products
Topic: 730/830 low power?
Replies: 7
Views: 7176

Re: 730/830 low power?

It is not programable,but is adjustable by the power control. I am sure you could mugwump the aux button to switch in some addtl circuit in the power control.
mod
by n5tbu
Wed Jan 09, 2008 8:52 pm
Forum: Kenwood Commercial Products
Topic: 730 prgramming issues.
Replies: 3
Views: 4844

Re: 730 prgramming issues.

You need a newer firmware IC.
mod
by n5tbu
Tue Jan 01, 2008 12:30 pm
Forum: Kenwood Commercial Products
Topic: kenwood krk-4db programming
Replies: 6
Views: 6867

Re: kenwood krk-4db programming

Also,you need to select dual band in your software.
mod
by n5tbu
Fri Dec 28, 2007 8:44 am
Forum: Kenwood Commercial Products
Topic: 30 series Accessory Connector source
Replies: 4
Views: 6227

Re: 30 series Accessory Connector source

Your local electronics store should carry them,it is a standard molex item.
mod
by n5tbu
Wed Dec 19, 2007 7:23 pm
Forum: Kenwood Commercial Products
Topic: Kenwood TK480 Programming Problem.
Replies: 8
Views: 8972

Re: Kenwood TK480 Programming Problem.

Alex,when you create a new codeplug and try to program it in...what happens? do you get a model type mismatch?
mod
by n5tbu
Wed Dec 19, 2007 8:34 am
Forum: Kenwood Commercial Products
Topic: TK-760 Display "P"
Replies: 1
Views: 2754

Re: TK-760 Display "P"

It means piority,if it is on every channel,it is programmed as selected channel priority for scanning.
mod
by n5tbu
Mon Dec 17, 2007 5:18 pm
Forum: Kenwood Commercial Products
Topic: tk-290 belt swivel
Replies: 1
Views: 3098

Re: tk-290 belt swivel

Here is the correct part number for you to Google,this goes with the leather case:

KLH-6SW

mod
by n5tbu
Mon Dec 17, 2007 5:13 pm
Forum: Kenwood Commercial Products
Topic: Kenwood TK480 Programming Problem.
Replies: 8
Views: 8972

Re: Kenwood TK480 Programming Problem.

I just checked my software and see the 480 and 880 are the same software.I know for a fact the 880 followed the above post and the old software would not work,prob is your problem with your 480's.
mod
by n5tbu
Mon Dec 17, 2007 5:08 pm
Forum: Kenwood Commercial Products
Topic: Kenwood TK480 Programming Problem.
Replies: 8
Views: 8972

Re: Kenwood TK480 Programming Problem.

I pulled the manual thinking that there was a program mode procedure,Not the case. The PC software does it for you. Has that cable and/or PC worked on other Kenwoods? A few Kenwood models were changed in production and needed a new software which was backwards compatable,you may have the old softwar...