Search found 412 matches
- Mon Oct 03, 2011 3:00 pm
- Forum: Kenwood Commercial Products
- Topic: TK-7180H
- Replies: 2
- Views: 5712
Re: TK-7180H
I have never seen that error! Was/is the radio working as is? Did it come from someone who possibly screwed up the programming? You can try starting from scratch,write a program with the model that the radio is supposed to be,then write that to the radio,when prompted tell it to overwrite,then try r...
- Sun Sep 25, 2011 2:40 pm
- Forum: Kenwood Commercial Products
- Topic: Programming a TK-240D
- Replies: 18
- Views: 20288
Re: Programming a TK-240D
redbird wrote:Is there a squelch adjustment on the 240?
Yes,pull the volume knob and you will see the sq with no knob,adjust as needed.
- Wed May 04, 2011 2:29 pm
- Forum: Kenwood Commercial Products
- Topic: Need help with TK 378g
- Replies: 1
- Views: 3846
Re: Need help with TK 378g
More than likely,yes.
- Sun Sep 05, 2010 5:55 am
- Forum: Kenwood Commercial Products
- Topic: TK-630 flashing "GR1-CH1" on the display, totally
- Replies: 10
- Views: 11076
Re: TK-630 flashing "GR1-CH1" on the display, totally
Thanks for the reply - I did that, but it still comes up flashing the GR1 - CH1 when it powers back on. I can repeat the cycle to set it into program mode, shut it off, then back on - but still the same response. Any ideas? The VCO could be unlocked....did the problem start after you put some new f...
- Mon Jun 29, 2009 8:44 am
- Forum: Kenwood Commercial Products
- Topic: Kenwood TK-762G type 1 mod to make it type 2?
- Replies: 4
- Views: 5840
Re: Kenwood TK-762G type 1 mod to make it type 2?
Haven't done field day in years,I'm pretty much inactive,doing radio for a living takes the fun out of hamming.
mod
mod
- Mon Jun 29, 2009 8:25 am
- Forum: Kenwood Commercial Products
- Topic: Kenwood TK-762G type 1 mod to make it type 2?
- Replies: 4
- Views: 5840
Re: Kenwood TK-762G type 1 mod to make it type 2?
The radio will program and work fine in the 2 meter range.
mod
mod
- Tue Mar 31, 2009 6:46 am
- Forum: Kenwood Commercial Products
- Topic: TK-862 issue
- Replies: 1
- Views: 3877
Re: TK-862 issue
Sounds like a cold solder connection....but where! Remove and re solder anything that looks questionable,good luck!
mod
mod
- Fri Mar 27, 2009 8:51 am
- Forum: Kenwood Commercial Products
- Topic: Tk 830 constant speaker output
- Replies: 13
- Views: 11659
Re: Tk 830 constant speaker output
Kenwood KLF-2 line filter.
mod
mod
- Tue Jan 13, 2009 8:01 am
- Forum: Kenwood Commercial Products
- Topic: field programming a tk-270?
- Replies: 1
- Views: 4185
Re: field programming a tk-270?
To place unit in programming mode: With power OFF, hold down the ! button (upper side button above PTT (Push-To-Talk) key with a square molded on it) with left index finger and the DIAL button with left thumb. Turn on unit. Hold buttons down until SEL appears on the display. Release buttons. Press T...
- Wed Nov 26, 2008 3:07 pm
- Forum: Kenwood Commercial Products
- Topic: Kenwood KPG-49D question
- Replies: 3
- Views: 5368
Re: Kenwood KPG-49D question
When you start the program it will show what radios it will program,before you hit "any key"
mod
mod
- Wed Nov 26, 2008 3:03 pm
- Forum: Kenwood Commercial Products
- Topic: tk-260(G) channel switch replacement
- Replies: 1
- Views: 3738
Re: tk-260(G) channel switch replacement
Yes,still available.
- Tue Nov 18, 2008 8:11 am
- Forum: Kenwood Commercial Products
- Topic: Remote Mic for TK-7160
- Replies: 2
- Views: 3977
Re: Remote Mic for TK-7160
Kenwood had a bulletin on this subject after many dealers complained. I can't locate it at the moment,but it was far too involved. It is easier to tie into the rear of the mic jack. The mics need to be modified because the mic elements are always hot.Pyramid has the mic mods documented on their webs...
- Fri Nov 07, 2008 9:59 am
- Forum: Kenwood Commercial Products
- Topic: TK-260 Programming Issue and Cloning
- Replies: 1
- Views: 3362
Re: TK-260 Programming Issue and Cloning
Might just be a bad channel switch,are the clicks positive or loose and sloppy?
mod
mod
- Tue Nov 04, 2008 9:20 pm
- Forum: Kenwood Commercial Products
- Topic: TK-X90 buttons/Inserts
- Replies: 1
- Views: 3012
Re: TK-X90 buttons/Inserts
send me a snail mail address and i will send some to you.
mod
mod
- Tue Nov 04, 2008 9:17 pm
- Forum: Kenwood Commercial Products
- Topic: 690 out of band?
- Replies: 2
- Views: 4156
Re: 690 out of band?
Even the 630 is not that wideband ! I have a few doing 37-54 with the band edges at .5uv and inbetween at .2uv,power is fairly consistant.
The 690 ain't even gonna come close.
mod
The 690 ain't even gonna come close.
mod