Phoenix Coverage

Forum dedicated to the Harris PSPC Product group items such as Orion, M7100/M7200/M7300, P7100/P7200/P7300, Harris Unity XG-100, GE Orion, GE Master Repeaters, EDACS Trunking, Pro Voice, PC Configure, RPM, and other topics relating to Harris, MA-Comm, Ericsson, GE products.
Post Reply
JerryReed
Posts: 4
Joined: Mon Feb 23, 2004 8:15 pm
Location: Kansas

Phoenix Coverage

Post by JerryReed »

Greetings,
I am looking at a Phoenix-SX on eBay.
The comb number is n5hh1w40tb .
Online information indicates the bandsplit as 150-174 MHz.
http://www.hallelectronics.com/getech/n52.htm
However, many of the eBay listings claim this comb has a split of 136-174 MHz.
Can anyone clarify this for me? I want to use this radio for APRS at 144.390 MHz.
Thanks in advance.
Mike KC0IWH
jim202
Posts: 123
Joined: Sat Mar 29, 2003 9:47 am
Location: New Orleans region

Re: Phoenix Coverage

Post by jim202 »

[quote="JerryReed"]Greetings,
I am looking at a Phoenix-SX on eBay.
The comb number is n5hh1w40tb .
Online information indicates the bandsplit as 150-174 MHz.
http://www.hallelectronics.com/getech/n52.htm
However, many of the eBay listings claim this comb has a split of 136-174 MHz.
Can anyone clarify this for me? I want to use this radio for APRS at 144.390 MHz.
Thanks in advance.
Mike KC0IWH[/quote]

Mike,

I don't have my books available to look upthe model number. Your probably going to find that it is the 150 to 174 range radio. In my years working with the Phoenix there are a couple of models you will fins. There is the crystal version, not many of these left areound. Most have long since been trashed. There is the narrow band Phoenix S and then there is the Phoenix SX. The SX is the model of choice. It will cover a much wider spread of RF frequency range than the S.

In the numbers that I have put onto 2 meters, some of the S models have required to have caps added to the tuned circuits. I use small silver mica caps and solder them to both the top and bottom side of the RF front end. Kind of depends on which circuit and how energetic I felt. With out the caps, you will find the receiver lacks good sensitivity on the bottom end.

Jim
k2hz
Posts: 150
Joined: Sun Jan 30, 2005 1:02 pm
Location: Rochester, NY

Post by k2hz »

The general Phoenix specs say "136-174" but the actual Phoenix SX radios are either of 2 bandsplits:

N5HH 150-174
N5GG 136-153

The N5HH1W40TB is 150-174, 40 W, 16 Channel (2 modes, 8 ch each), Non-scanning.

I have used a "HH" Phoenix for local repeaters on the high end of 2M (146-147) with slight degredation but the preformance rolls off pretty bad lower in the band.

Dick, K2HZ
JerryReed
Posts: 4
Joined: Mon Feb 23, 2004 8:15 pm
Location: Kansas

How about MVS?

Post by JerryReed »

I can use an MVS instead. I would have to send it out for programming though as I can't seem to find the software anywhere.

Does anybody know how the MVS behaves around 144.390? The bandsplit for the ones I found are 150-174 MHz as well.
Mike
User avatar
KF4SQB
Posts: 166
Joined: Tue Dec 16, 2003 12:42 am
Location: Moultrie GA

Post by KF4SQB »

I'm running a high-split Phoenix SX as a Ham base here, have made no mods to it, and it works great. On the other hand, I don't have anything below 145 in it, so I can't say how it is at the extreme bottom of the band.
Brett Kitchens
KF4SQB

kf4sqb "at" wetsnet "dot" com

Of all the things I've lost, it's my mind I miss the most.......
Post Reply